ASTM B265 PDF

ASTM Gradel, JIS Grade, TIA, RMI 25, TIMETAL 35A, ST Sheet and plate. ASTM B Gr1, Mil-T CP Bars and billets. ASTM B Gr1. Tube. ASTM B Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality Titanium Plates, Sheets & Coils, Titanium sheets & plates.

Author: Kesar Kajirisar
Country: Hungary
Language: English (Spanish)
Genre: Education
Published (Last): 8 December 2008
Pages: 112
PDF File Size: 10.35 Mb
ePub File Size: 11.58 Mb
ISBN: 979-4-82787-242-5
Downloads: 68626
Price: Free* [*Free Regsitration Required]
Uploader: Sarn

Grade 2H, 7H, 16H, and 26H are intended primarily for pressure vessel use. For plates up to 10 in. If shipped as descaled, sandblasted, or ground, the manufacturer shall be permitted to remove minor surface imperfections by spot grinding if such grinding does not reduce the thickness of the material below the minimum permitted by the tolerance for the thickness ordered. Mechanical properties for conditions other than annealed or plate thickness over 1 in.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Ingot hydrogen need not be reported. Methods of Chemical Analysis Sampling for Chemical Analysis 9. MPa If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Only original conforming test results or the conforming retest results shall be reported to the purchaser. The bend specimen may be of less than full material thickness; however, the outer surface of the specimen must include the original material surface with no material removal or surface conditioning other than at the rounded corners, and must otherwise be representative of the product as supplied.

Committee B10 has identied the location of selected changes to this standard since the last issue B – 08b that may impact the use of this standard.

ASTM B _图文_百度文库

NOTE 4—The maximum deviation from a at surface does not customarily exceed the tabular tolerance for the longer dimension specied. The values given in parentheses are mathematical conversions to Wstm units that are provided for information only and are not considered standard. This is in accordance with the round-off method of Practice E In cutting samples for analysis, the operation should be carried out insofar as possible in a dust-free atmosphere because utmost care must be used in sampling titanium for chemical analysis due to its great affinity for elements such as oxygen, nitrogen, and hydrogen.

  LION BEAVER OTTER GOLDEN RETRIEVER TEST PDF

This abstract is a brief astmm of the referenced standard. The frequency of the retest will double the initial number of tests.

Aluminum Vanadium Palladium Ruthenium 0. The markings shall have no deleterious effect on the material or its performance. Other elements may be present in titanium or titanium alloys in small quantities and are inherent to the manufacturing process.

Your comments are invited either for revision of this standard or for additional standards astk should be addressed to ASTM International Headquarters.

Titanium Plates, Sheets & Coils

Unalloyed titanium plus 0. Annealed material may be furnished as descaled, as sandblasted, or as ground, or both sandblasted and ground. The characters shall be sufficiently stable to withstand ordinary handling. Product analysis tolerances cover variations between laboratories in the measurement of chemical content of the specimen.

For circles, the over thickness tolerances in this table apply to the diameter of the circle corresponding to the width ranges shown.

There is no under tolerance in weight for titanium sheets, under tolerance being restricted by the permissible thickness variations. Each pair of these bends will place opposite surfaces of the sheet or plate material in tension. Samples for analysis should be stored in suitable containers. G Properties for material in the solution treated condition. Current edition approved May 1, The values given in parentheses are mathematical awtm to SI units that are provided for information only and are not considered standard.

  INSTRUCTIVO FORMATO 1732 PDF

Other elements may not be added intentionally. Approved May 1, When the aztm edge is placed on a single high point, the maximum deviation from the plate at each end shall be no greater than 0. The report shall include results of all chemical analysis, tensile tests, and all other tests required by the specication.

For sheet and strip, the bend test astj shall stand being bent cold v265 without fracture v265 the outside of the bent portion. The test report shall, at minimum, indicate acceptable or unacceptable results.

B Bend to Radius of B2265, T equals the thickness of the bend test specimen. D Other elements need not be reported unless the concentration level is greater than 0.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk zstm infringement of such rights, are entirely their own responsibility. Link to Active This link will always route to the current Active version of the standard. Specimens shall be taken from sheet or plate material produced from the same ingot or wstm materials, processed the same way to the same nominal thickness, width and length, produced in one production run or campaign, nished in the same way, and otherwise representative of the material supplied.

Heat numbers shall occur at least 3 times across the width of the sheet and at intervals not greater than 2 ft 0. In widths over 16 to in.

The zstm analysis shall be conducted by the standard techniques normally utilized by the manufacturer and purchaser. Bend tests are not applicable to material over 0. Permission rights to photocopy the standard may also be secured from the ASTM website www.