General Description. The LP and LP are micropower voltage regulators with very low dropout voltage (typically 40mV at light loads and mV at. LPLPRE3 Texas Instruments LDO Voltage Regulators FIXED MICROPWR VLTG REG datasheet, inventory, & pricing. The LP and LP are micropower voltage regulators with very Careful design of the LP/LP has minimized all . See MIL/AERO Datasheet.
|Published (Last):||23 August 2018|
|PDF File Size:||1.88 Mb|
|ePub File Size:||16.34 Mb|
|Price:||Free* [*Free Regsitration Required]|
Fortunately, I disconnected it quickly enough to prevent any obvious permanent damage to the regulator. It looks like the detector is on the same side as the display – does this mean you are checking yourself for radiation rather than pointing it at a source in front of you?
I especially like the plated through holes, which are fantastic for prototyping if you have to remount components several times. I could post the entire project if you think it would help sales of the ATtiny26 board.
Of course we had these boards made in a batch, so now each time I populate one I have to bypass the power switch with tweezers to to clear that fuse. For one low-power project, I have the possibility of powering the board from either a 9V solar cell or a 4. I just tried taking a regulator part not on a board and applied from 4.
Can you try doing the regulator test again? The program currently occupies out of bytes of program memory. What puzzles me is that the regulator encounters this situation every time the external source is switched off and there are capacitors in the circuit that must be discharged, so there is some reason to think that dwtasheet a transient backflow is not damaging.
The LP data sheet does not give any insight into this situation. What I like about the ATtiny26 board is the convenient arrangement of two ports with access to power and ground at several points, coupled with the well-laid out prototyping area.
Shop Blog Forum Support. I could post the entire project if you think it would help sales of the ATtiny26 board I do intend to buy a few more — the sale price is very attractive, so be sure and save me a couple! Since datashest is some interest, my Geiger counter is based on a circuit described by Tom Napier in Circuit CellarNovember I can always use diodes to switch between solar and backup supply, but Datasheft thought I could float charge the battery without such trickery.
Beta and gamma radiation are much more penetrating so the direction the tube is pointing is less important and is actually irrelevant for gamma radiation.
The HV generator is top right, leading to the connector for the V tube bias red datassheet. I had to jump! We would probably buy a few, especially if the footprint was compact. There is a small current draw increase at 5. The unit is currently monitoring the cosmic background radiation in my office 95 counts in seconds. I expect that the regulator can tolerate this but it might add some unnecessary current drain.
Did you look at the datasheet from that company? The JTAG fuse comes datasjeet, which makes some pins start up set high. It features an internal V power supply 2 mA total draw!
Both have a thin and very delicate metalized membrane for measurement of alpha radiation.
We even had some ATmega8 versions made, but we never sold them there were some other factors besides the ATtiny26 board not doing well, such as the mega coming out and the move to 6-pin ISP connectors.
By the way, I really like the board design. Where did you get your Geiger tube? I suspect that no long term damage should result from this misuse, as long as one does not exceed other component ratings. I do that sort of thing all the time, and I have had datashee problems.
LP Datasheet UTC pdf data sheet FREE from
There is one error in the published circuit: Can you tell me what you like about it? Well, I connected a datazheet. The board is shown below. By the way, there are a lp9250 manufacturers of the part, and your board probably has the one from On Semiconductor.
Is the RS option useful? My power supply current-limited at about 1 amp. Not realizing this we designed our main board which uses the pushbutton power switch with one of these connected to the OFF pin.
Daasheet most recent project with the ATtiny26 board is a Geiger counter. The counter input INT0 is marked with a green arrow. If only the ATtiny26 had a bit more memory… Thanks, Jim. I do intend to buy a few more — the sale price is very attractive, so be sure and save me a couple!
In my version, the tube is screened so that small sources can be set right on top of the detector. See below for the exterior appearance. The rainbow cable leading off screen goes to the two pushbuttons datasueet the LCD.
Thanks for checking on the regulator — maybe I shorted the power supply while hooking things up. If Dwtasheet connect the 4. The C program and the two buttons provide a menu-based system to set up data collection parameters and do the counting.